另类天堂网不卡另类系列-日韩你懂的-亚洲视频一二三-日韩午夜在线观看-av永久免费在线观看-老妇荒淫牲艳史-亚洲 欧美 综合-性色av一区二区三区夜夜嗨-无码人妻出轨黑人中文字幕-日韩av无码中文无码电影-57pao国产成永久免费视频-未满十八18禁止午夜免费网站-免费一级日韩欧美性大片-国产亚洲精品一区在线播放-亚洲天堂av网

 

Features: door opening mode: front door opening and side door opening control accuracy: ± 1 ℃ furnace temperature uniformity: ± 1 ℃.

 

Easy to operate, programmable, PID self-tuning, automatic temperature rise, automatic heat preservation, automatic temperature drop, no need to be on duty; it can also be equipped with computer communication to operate the electric furnace through computer (start electric furnace, stop electric furnace, pause temperature rise, set temperature rise curve, temperature rise curve storage, historical curve, etc.), software free of charge see: computer control system.

 

Fast temperature rise (adjustable temperature rise rate from 1 ℃ / h to 40 ℃ / min).

 

Energy saving (the furnace is made of imported fiber, which is resistant to high temperature and quench)

 

The furnace body is corrosion-resistant and acid-base resistant through fine plastic spraying, and the furnace body and furnace are isolated by air-cooled furnace wall temperature close to room temperature.

 

Double circuit protection (over temperature, over pressure, over current, section couple, power failure, etc.)

 

Furnace material imported refractory material, good heat preservation performance, high temperature resistance, fast cooling and heat resistance

 

Temperature category: 1000 ℃ 1200 ℃ 1400 ℃ 1600 ℃ four kinds

 

High temperature hot pressing furnace is a periodic operation type, which is widely used in cemented carbide, functional ceramics, powder metallurgy, etc. for hot pressing and sintering under the conditions of high temperature and high vacuum. It can also be used for hot pressing and sintering under the condition of inflation protection.

 

Advantages and disadvantages of hot pressing furnace

 

Advantages of hot pressing:

 

(1) greatly reduce the forming pressure. The pressure used in hot pressing is only about 1 / 10 of that of cold pressing, so hot pressing can press large products.

 

(2) shorten the sintering time.

 

(3) the influence of powder size and hardness on hot pressing process is not obvious, so hot pressing can press some hard and brittle powder.

 

(4) when hot pressing, the powder has good plasticity and can be pressed into sheet, thin-walled tube and other special products.

 

 

 

Disadvantages of hot pressing:

 

(1) it is difficult to select the die material because of its high requirements, and the die life is short and the cost is large.

 

(2) single piece production, so the production efficiency is low.

 

(3) the surface of the product is rough and the accuracy is low, which generally needs cleaning and machining.

 

(4) high power consumption, high product cost.

 

 

 

There are three heating methods of hot pressing: Indirect resistance heating, direct resistance heating and induction heating. The figure is the schematic diagram of hot pressing heating mode. The resistance indirect heating mode is that the electric current is heated through the graphite tube, and the pressing die loaded with powder is put into the graphite tube. The resistance direct heating mode can be divided into two cases: the current passing through the die material to generate heat (B in the figure) and the current passing through the die material to generate heat. Induction heating is to use the current excited by electromagnetic induction to heat the die.

 

 

 

V. when the working temperature of hot pressing is below 800 ℃, high speed steel and other heat-resistant tool steel can be selected as the material of hot pressing die; when the working temperature is 1500-2000 ℃, graphite should be used as the material of hot pressing die, but the pressure that graphite can bear is much lower than the former. Therefore, for the process of low temperature and high pressure, we can choose metal mold or hard alloy mold; for the process of high temperature and low pressure, we should choose graphite mold.